This section contains a quick and dirty explanation of the embedded Linux development process. Embedded Linux is a topic with many interdependencies; this section lays out the big points and purposely lacks detail so you can see the big picture without getting distracted by the fine details. The heft of this book should indicate that more details are forthcoming.
Target Hardware
Nearly every project involves selecting the processor to be used. A processor is just a chip and not much more until it’s soldered on a board with some peripherals and connectors. Processor vendors frequently create development boards containing their chip and a collection of peripherals and connectors. Some companies have optimized this process to the point that a board with connectors and peripherals is connected to a small daughter board containing the processor itself, allowing the base board to be shared across several different processor daughter boards.
Development boards are large, bulky, and designed to be easily handled. Every connector is supported by the processor because the vendor wants to create only one board to ship, inventory, and support. The development kit for a cell phone occupies as much space as a large laptop computer. In a majority of products, the development board isn’t used in the final product. An electrical engineer lays out a new board that fits in the product’s case and contains only the leads for the peripherals used in the final application, and he probably sneaks in a place to connect a serial or JTAG port for debugging.
Obtaining Linux
Linux is nearly always included with a development board and has support for the peripherals supported by the chip or the development board. Chances are, the board was tested with Linux to ensure that the processor and connectors work as expected. Early in the history of embedded Linux, there were porting efforts to get Linux running on a board; today, this would be an anomaly. If the board is an Intel IA-32 (frequently called x86) architecture, you can boot it (under most circumstances) with any desktop distribution of Linux. In order to differentiate their IA-32 boards, vendors frequently include a Linux distribution suitable for an embedded project.
Just as the development board has every known connector, the Linux included with the board is suited for development and not for final deployment. Part of using Linux is customizing the kernel and the distribution so they’re correct for the application.
Booting Linux
Because most board vendors supply a Linux distribution with a board, getting Linux booted is about configuring the software services Linux needs to boot and ensuring the cabling is proper and attached. At this point, you probably need a null modem serial cable, a null modem Ethernet cable (or a few cables and an Ethernet concentrator or switch), and maybe a USB cable. Unlike a desktop system with a monitor, the user interface for an embedded target may be just a few lights or a one-line LCD display. In order for these boards to be useful in development, you connect to the board and start a session in a terminal emulator to get access to a command prompt similar to a console window on a desktop Linux system.
Some (enlightened) vendors put Linux on a Flash partition so the board runs Linux at power up. In other cases, the board requires you to attach it to a Linux host that has a terminal emulator, file-transfer software, and a way to make a portion of your Linux system’s hard drive remotely accessible. In the rare cases where the board doesn’t include Linux (or the board in question hails from before you welcomed the embedded Linux overlords), the process requires you to locate a kernel and create a minimal root file system.
Development Environment
Much of the activity around embedded development occurs on a desktop. Although embedded processors have become vastly more powerful, they still pale in comparison to the dual core multigigabyte machine found on your desk. You run the editor, tools, and compiler on a desktop system and produce binaries for execution on the target. When the binary is ready, you place it on the target board and run it. This activity is called cross-compilation because the output produced by the compiler isn’t suitable for execution on your machine.
You use the same set of software tools and configuration to boot the board and to put the newly compiled programs on the board. When the development environment is complete, work on the application proper can begin.
System Design
The Linux distribution used to boot the board isn’t the one shipped in the final product. The requirements for the device and application largely dictate what happens in this area. Your application may need a web server or drivers for a USB device. If the project doesn’t have a serial port, network connection, or screen, those drivers are removed. On the other hand, if marketing says a touch-screen UI is a must-have, then a suitable UI library must be located. In order for the distribution to fit in the amount of memory specified, other changes are also necessary.
Even though this is the last step, most engineers dig in here first after getting Linux to boot. When you’re working with limited resources, this can seem like a reasonable approach; but it suffers from the fact that you don’t have complete information about requirements and the person doing the experimentation isn’t aware of what can be done to meet the requirements.
Source of Information : Pro Linux Embedded Systems (December 2009)
No comments:
Post a Comment